Addonics Technologies SCHD SA-FW Manual de usuario Pagina 241
- Pagina / 408
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Install the S8300
Issue 12 May 2009
241
Install Authentication Screen
2. Select Install the license file I previously downloaded and click Submit.
The system displays the License File Install Results screen.
3. Click the Restart CM button, if it is displayed on the screen.
4. Verify the license and authentication file installation by issuing the statuslicense -v
command from the server command line:
● The License Mode should be Normal.
● The report should list a License Serial Number.
If the server is an LSP, stop and start Communication Manager
Note:
Note: Skip this task if you used the Restart CM button just after loading the license file
for this LSP. See, Installing the Communication Manager authentication files
on
page 240.
If you are upgrading an LSP, you must restart Communication Manager to sync the license for
LSP status.
1. Access the server’s command line interface using an SSH client, like PuTTY, and an IP
address of 192.11.13.6.
2. Type stop -caf.
3. Type start -ca.
- S8300 Server 1
- Issue 12 May 2009 5 5
- Issue 12 May 2009 7 7
- Issue 12 May 2009 9 9
- Contents 10
- Issue 12 May 2009 11 11
- Issue 12 May 2009 13 13
- Issue 12 May 2009 15 15
- About this book 17
- Conventions 18
- Terminology 19
- Typography 20
- Downloading this book 21
- Related resources 22
- Technical assistance 23
- Trademarks 24
- Documentation 24
- Sending us comments 25
- Section 1: Reference 27
- What wizards are available 29
- When to use each wizard 30
- About connection methods 37
- Terminal Emulator, or ASA): 39
- About log in methods 44
- To run telnet 45
- To run the Web Interface 46
- Welcome Screen 47
- 4. Click the Continue button 47
- Login Screen 48
- 6. Log in as craft 48
- To run SAT: 50
- To start Site Administrator 53
- Communication Manager 54
- About hardware components 55
- What is the S8300 Server 56
- Manager Messaging 58
- Maintaining system security 59
- Terminal server installation 60
- Administering the IOLAN+ 63
- To connect the IOLAN+ 64
- ● Name: 66
- ● IP address: (for IOLAN+) 66
- ● Subnet mask: 66
- To reboot the IOLAN+ 67
- Administering the gateway 68
- Administering an IOLAN+ port 68
- ● Remote Port: 0 70
- Administering IP services 72
- To administer IP services 73
- Call detail recording (CDR) 74
- Administering CDR parameters 75
- To administer CDR parameters 76
- CDR LINK STATUS 77
- Primary Secondary 77
- Maintenance Busy? no 77
- Downloading the RDTT package 78
- Installing the RDTT package 78
- Related topics 78
- Printers 79
- DS1/T1 CPE loopback jack 80
- Administering a loopback jack 82
- To test the DS1 span 83
- To restore DS1 administration 86
- MM710 multi-media module 89
- External modems 95
- Recommended Modems 96
- MT9234ZBA-USB 96
- Music-on-hold 98
- 123456 87 100
- E1/T1 EIA 530A DCE 100
- EISO EMSM EOSI 100
- Adjunct Information Sources 103
- ASAI and DEFINITY LAN Gateway 104
- Avaya Interactive Response 104
- Call Accounting Systems 105
- SIP Enablement Services 105
- Section 2: S8300 Server 107
- Related Documentation 108
- Issue 12 May 2009 109
- Installation Overview 110
- Name and number list 113
- Custom template 114
- To download a service pack 115
- Completing the RFA process 117
- To run the ART 119
- (Avaya technicians only) 119
- Install the S8300 120
- Accessing the S8300 121
- Setting telnet parameters 122
- Verifying Software Version 124
- Creating a super-user login 124
- To create a login: 125
- ● Server Type 126
- ● Media Gateway Serial Number 126
- 13. Click Continue 130
- 21. Click Continue 133
- 22. Click Continue 134
- 23. Click Continue 135
- 26. Click Continue 137
- Telephony configuration 143
- 2. Click Continue 144
- 3. Click Continue 144
- 4. Click Continue 145
- Trunk configuration 147
- ● Adding a trunk 148
- ● Modifying trunk parameters 148
- ● Displaying trunk status 148
- ● Removing a trunk 148
- Adding a trunk 149
- Modifying trunk parameters 150
- Displaying trunk status 152
- Removing a trunk 153
- Endpoint installation 155
- Alarm configuration 156
- Password and final screens 158
- 6. Click Continue 161
- 7. Click Continue 162
- Gateway Device Manager 162
- To enable SES 164
- To verify SES is enabled 164
- To reset the system 165
- Administering Network Regions 166
- To define IP network region 1 167
- Administering IP Interfaces 169
- ● Administering IP Interfaces 172
- To add a media gateway 183
- To verify changes 185
- To save translations 186
- Manager for CM Messaging 187
- Administering SES 187
- SES administration tasks 189
- Survivable Processor 190
- Split registration solution 192
- Sequence of events 193
- (if the Primary Controller) 194
- Saving translations 198
- Backing up system data 198
- ● Host Name 200
- ● Directory 200
- Final tasks 201
- S8300C to release 5.2 203
- Important: 204
- Section 3: Manual 205
- Issue 12 May 2009 207 207
- Verifying software version 221
- Configuring the S8300 226
- ● The key number 238
- ● The encryption type 238
- ● The key code 238
- To create the key file 239
- To upload the keys file 239
- Processor Ethernet 260
- Adding a media gateway 265
- Verifying changes 267
- ● OSS Method 276
- ● SNMP Method 276
- Controller) 278
- S8300C to Release 5.2 287
- Obtaining S8300 software 293
- Obtaining service pack files 294
- Post-upgrade service pack 295
- To disable alarm origination 310
- (if IA770 is being used) 311
- To determine other languages 313
- Shutting down IA770 315
- ● This server’s CD-ROM drive 326
- Upgrade the S8300 329
- To install update files 336
- Install the SES license 337
- Making the upgrade permanent 341
- Post-upgrade tasks 344
- RFU) files, if any 345
- ● Telephones have dial tone 348
- Backing up the system 350
- Overview 351
- 998 8 8888 8 8 352
- 89 9 9 9999 9 9 352
- 88 8 8 8 8 9 9 9 9 352
- Issue 12 May2009 353
- Configuring your laptop 355
- Accessing S8300 A/B/C Server 355
- To check reboot progress 376
- Enable SES 380
- Verifying connectivity 381
- Restoring backup data 381
- Installing the SES license 386
- Rebooting the server 388
- Integrity check 389
- If CM Messaging is installed 389
- ● Messaging Web Pages 390
- ● Server command line 390
- If the S8300 is an LSP 391
- Starting CM Messaging 396
- Numerical 403
© 2020, manymanuals.es. Todos los derechos reservados | 0.076 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales